For Accessories Side Stickers Racing Stripes Race Door Decals

Car Side Stickers Racing Stripes Vehicle Universal Race Stripes Door Decals Skirt Vinyl Film Exterior Stickers for Accessories

Product Name: Car stripe side body Decal

Installation notes:

1. Clean the body and keep it dry. 2. In general, first tear the bottom to determine the position to be pasted, and then slowly tear the bottom paper while scraping with a tool (the tool can be bank card). 3. If the figure is not large (less than 20cm), you can also tear off all the backing paper before pasting. But we must pay attention to tear it slowly, and be careful not to stick the car stickers down or cause accidental adhesion. 4. After affixing, repeatedly scrape and press for several times, and slowly tear off the transparent transfer film. 5. Done. (do not wash the car for 2-3 days)
2, Pasting methods of medium-sized stickers (such as door stickers, map stickers, spare tire stickers, etc.):
1. Clean the body and keep it dry. (don't do it in the strong wind, rain or sun, you can choose the shelter in the garage, etc.) 2. First tear the bottom to determine the position to be pasted, and then slowly tear the bottom paper while scraping it with a tool (the tool can choose the bank card). 3. But we must pay attention to tear it slowly, and be careful not to stick the car stickers down or cause accidental adhesion. 4. After affixing, repeatedly scrape and press for several times, and slowly tear off the transparent transfer film. 5. Done. (do not wash the car for 2-3 days, two people are recommended)
3, Large car stickers:
1. The large stickers are rolled up for delivery when they are delivered. If there are some bubbles or wrinkles in the bottom paper and transfer film of the stickers, please note that this is normal and does not affect the car stickers. Before the stickers are pasted, the car stickers should be laid on a flat desktop and scraped with a scraper (bank card). 2. It is suggested to go to car beauty salon and ask for help. Choose a do it yourself buyer, suggest posting home to consult the seller. Methods: (dry or wet sticking can be used)
(1) Dry paste method: (the following method is used for the whole big paste, and the following method is not used for collage) 1. Clean the car body and keep it dry. (don't do it in the strong wind, rain or sun, you can choose the shelter in the garage, etc.) 2. First, compare the car on the car, determine the position to be pasted, and try to avoid the concave and convex or difficult position. 3. Then you can take a little tape or cut off the transfer film to fix the car stickers and start to paste. 4. First, tear off the bottom from the front of the car to determine the position to be pasted, and then slowly tear off the bottom paper while scraping with a tool (the tool can be bank card). 5. But we must pay attention to tearing slowly, not leaving bubbles, and not sticking the car stickers or causing accidental adhesion. 6. After pasting, repeatedly scrape and press for several times, and slowly tear off the transparent transfer membrane. 7. At the beginning of the later work, first cut the middle of the door with a knife (gap or opening position), and stick it inward. 8. If there are bubbles, you can try to scratch them again. The big bubbles can be broken directly. If there are small bubbles, you can wait a few days before they are fully bonded. 5. Be sure to check it again when you are finished. (don't wash the car for 2-3 days, 2-3 people are recommended)
(2) Wet sticking method - car stickers or large car stickers are applicable [it is recommended to take them to the car ] steps of wet sticking method - tools: watering can, clean rag, scraper, art knife, air duct 1. After cleaning the car body, spray water with the watering can on the body part to be pasted & mdash; & mdash; is mainly used to reduce the viscosity of the sticker and facilitate the adjustment of the position. 2. After determining the position to be pasted, remove the transfer film (transparent adhesive film pasted on the reflective sticker) and the vehicle sticker from right to left [or from top to bottom] and press them on the vehicle surface with a rag, then paste, press flat with a rag and uncover the bottom paper at the same time. 3. In case of door handle or anti-collision strip, the material shall be cut and wrapped or loaded according to the situation. 4. Adjust the general position of the figure in time, and then wipe off the water and bubbles repeatedly with the scraper. When using the scraper, scrape diagonally from right to left. Finally, tear off the transparent transfer film. 5. In case of the door and the seam, use the art knife to divide them and stick them inward. 6. Try to let the moisture in the car stickers dry completely. If possible, it can be heated and dried moderately with the air duct.

Strong requirements: do not expose to the sun within 24 hours, and do not wash the car within 48 hours.

1 . We will send out your goods within 1-3 WORK DAYS after verification of the payment and confirmation of the order. We always try our best to ship as fast as we can, in case of any delay, we will inform you in advance.

2 .If the package is lost and you didn't get the package in 60 days, please contact us first,we will resend you a new vinyl and new tracking number.

3. We will send you tracking number after we send the package,all the item can be tracked online!

4. Usually delivery time will be 14-30 days.

     Brazil: Usually delivery day 14-70 days. Other country will be about 14-30 days. Need to proved VAT tax number, or, we didn't pay for any loss for your parcel.

     Russia also a little bit longer, need 14-40 days usually.

     If you don't get the package in 60 days or 30 days your package have no change in shipment, we will help you..

5. If you didn't get the package, and you want us the extend the delivery time limited, you can leave us comment in the order.

6. We are not responsible for any custom duty or import tax.